|
Our range of USB programmers all use the same freeware MicroPro software
with free lifetime updates. MicroPro is our own custom written programming
interface and will accept any hex or obj file for programming.
|
K8076 - PIC Programmer Board
 The
Velleman K8076 PIC programmer board can program a wide range of Microchip® PIC™ microcontrollers
as detailed below.
It connects to the computer PC serial port.
more info / ordering |
3128 - USB 'all-Flash' PIC Programmer with ICSP
 Professional
quality USB port 'all-Flash' PIC Programmer. No external power supply needed
making this a truly portable programmer. Ideal for field and general use.
5-pin ICSP programming lead.
more info / ordering
|
3149 - USB or Serial PIC Programmer with ICSP
 This
PIC Programmer is ideal for field and general use as it uses the USB or
Serial port. 6-pin ICSP programming lead. Programs a wide range of old and
modern PIC devices.
more info / ordering
|
3150 - USB PIC Programmer with ICSP
 Professional
quality PIC Programmer. Quick and convenient USB port connection makes it
ideal for use with modern and laptop computers. Reliable, high speed programming.
There is a 6-pin header cable for ICSP and Auto Program feature for fast
no-key-press bulk programming.
more info / ordering
|
3182 - USB Flash ICSP PIC Programmer
 This
is a fully assembled version of our 3128 USB Flash Microchip PIC programmer
but without the programming socket. It just has a 5-pin ICSP header (GND,
VCC, CLK, DAT, VPP). No external power supply needed making this a
truly portable programmer. Ideal for field and general use.
more info / ordering
|
|
|
K8048 / VM111 - PIC Programmer & Experimenter Board
 The
Velleman PIC Programmer & Experimenter Board is suitable for programming Microchip®
FLASH PIC™ microcontrollers.
Available in both kit and pre-assembled versions.
more info / ordering |
3081 - Introduction To PIC Programming
 Learn
programming from scratch using a P16F84.
The PIC16F84A has become the entry point for those wishing to learn PIC
microcontroller programming. This kit is based around the hardware to support
a two-part, practical, hands-on tutorial series magazine feature.
more info / ordering
|
|
|
3117 - 'PICALL' PIC Programmer (8 to 40 pin)
 Our
popular PICALL' will program virtually all 8 to 40 pin serial-mode*
AND parallel-mode (PIC16C5x family)* programmed PIC microcontrollers.
Connects to PC parallel port (EPP, ECP, SPP). complete with fully registered
programming interface software.
more info / ordering
|
3059 - P9 Programmer
 This
is a simple-to-use, low cost programmer for the 68HC705P9 micro-controller.
It can be used to program, verify and copy.
more info / ordering
|
3099 - K1 Programmer & Simulator
 This
simple-to-use, low cost kit is designed to provide I/O emulation for software
code simulation as well as allowing programming of 68HC705K1 micro-controller
devices.
more info / ordering
|
|
|
3151 - EEPROM Programmer
 Specifically
designed for programming 24 Series, I2C bus and SPI 93 Series serial EEPROM's.
You can use a 16 pin ZIF socket (not supplied) for volume programming. The
top 8 pins are for the 24 Series; the bottom 8 are for the 93 Series SPI
EEPROM's.
more info / ordering
|
|
|
| For microcontrollers chips - See
our Electronic Components page
|
|
|
 We
highly recommend this range of books supplied in association with
Amazon.com
|
|
|
|
|
|
|
|
|
